The density of milk: how to determine and what do the indicators depend on?

The density of milk: how to determine and what do the indicators depend on?

Milk has been consumed by humans for a very long time. For such a period, its density and useful properties have already been studied, the composition has been determined. The amount of mineral salts, vitamins and other useful elements in the drink depends on how responsibly the farmer approaches the issue of animal care. Moreover, density plays an important role, but to understand what this means, it is worth diving deeper into the issue.

What is it and how to determine

There is a special device that is used on an industrial scale. It is called a lactodensimeter or a hydrometer. To determine the density level, 200 milliliters of milk is poured into a measuring cup, the diameter of which should not exceed 5 centimeters. You can also check at home if you have such a device, there is a table by which you can compare the indicators.

The liquid is slowly poured along the walls into a container, filling it up to 2/3 of the volume. Install the device inside so that it is afloat, and wait for the result in a few minutes. The readings are confirmed by shaking the device a little and measuring again. In this case, the temperature of the milk should be at around 20 degrees.

If the last condition is not met, then 0.0002 should be added to the data obtained for each additional degree, if the temperature is lower, then it is subtracted.

Of course, such a device may not be available at home, so measurements are taken in a different way. To do this, you need to dilute a small amount of milk in water and wait.The milk will either sink to the bottom after a while, or spread out at the top. In the first case, we can conclude that it is of good quality, in the second - the opposite is true.

It is permissible to take not water, but alcohol, which are mixed and poured onto the bottom of the plate. In a diluted state, flakes are not formed, otherwise the process of protein coagulation will begin.

You will learn more about how to determine the density of milk in the following video.

What is measured and what is the norm

If we consider the physical properties of milk, then this indicator plays an important role. It is on its basis that it is determined how natural the drink is and in what percentage are fats in it. Speaking in a more complex, scientific language, the density demonstrates how much at a temperature of 20 degrees the mass is greater than that which distilled water has at a temperature of 4 degrees. Measure the value in grams or kilograms per cubic meter.

What factors affect performance

The density index depends on factors such as:

  • the presence of salts, sugar, protein and their quantity;
  • when the measurement is made;
  • the lactation period of the animal;
  • general health indicators;
  • what they feed;
  • breed;
  • season.

It is worth saying that immediately after milking, the density of milk is significantly higher. If the cow has recently given birth, then again, the density of the drink will be maximum, since nature ordered it so that in the first months of life the calf receives the maximum of useful substances for growth.

The quality of the feed should never be relegated to the last place, nor should the overall health of the cow. In particular, in winter, the animal does not receive the necessary substances, respectively, and milk contains fewer trace elements.

The value of this drink can range from 1.020 to 1.033 g/cm3. If, after measuring the indicator, it turns out that the value does not reach these parameters, we can definitely say that the drink was diluted with water. Everything can change depending on the temperature.

The lactation period plays an important role in determining the density of cow's milk. Approximately, the animal is able to give it 305 days, after calving, colostrum is produced by the udder. This goes on for up to ten days. It is not recommended to use it in food, because its composition is very different from the usual whole drink. It must be said that it contains a huge amount of antibodies, much more proteins and minerals, increased fat content. Saltish taste and bitter aftertaste are produced by enzymes and phospholicytes.

The density of colostrum is 1040 kg/m3, and the acidity on the Turner scale is 50 degrees.

Then the secretion of old-fashioned milk begins, which is also unsuitable for humans. The number of leukocytes is too high in it, the acidity is not so high, but the density is at the level of 1032 kg/m3.

To understand why these drinks are so harmful, it is enough to know that if one of them gets into normal milk, then it spoils, an unpleasant aftertaste cannot be drowned out by anything.

From a chemical point of view, milk is a complex product. It can contain both useful components and harmful to humans, for example:

  • pesticides;
  • heavy metal salts;
  • pathogenic microorganisms;
  • antibiotics.

In nature, the cow does not produce them, but consumes them. They do not disappear anywhere and are transmitted to a person through a drunk drink.When they talk about quality, they mean the proportions of vitamins, minerals, energy value and much more.

How to increase

The density can be raised, but this is not done by an artificial method, but simply by creating good conditions for the animal. It is important to properly and fully feed the cow, monitor her health. Quality always directly depends on how responsibly the farmer approaches the content. If a cow gives bad milk, then it is not healthy to eat it, as well as the products that can be prepared from it.

no comments
The information is provided for reference purposes. Do not self-medicate. For health issues, always consult a specialist.

Fruit

Berries

nuts